This whole thing may entirely not matter, and I suspect that's the case, but I'll ask away! I'm checking line lengths, and inconveniently my lines either end in loops or knots with no easy way to attach all 4 to a single point (unlike, for example, Ozone lines). I'm using small loops to attach to each line, then anchoring those.
For the knot ends I'm just attaching the loops like I would a kite.
For the loop ends (steering lines for me), I can either leave the loop fully open, or use the loop like I would on a kite, which shortens the lines a little.
This doesn't matter when checking steering line to steering line, or front line to front line. But how about checking steering line length vs front line length?
(I realise this is a small matter of adjusting the depower trim on the fly, but how do you do it? Does it even matter?)
Hi Sirlancelot,
It does matter when you are checking the line lengths for tuning that they are all attached evenly. Some lines are easy to attach using a screwdriver or your safety leash, but that's not always possible as you mentioned above.
Your methods works you just need to take into account the small difference in length during your tuning.
I designed and manufactured a tool for this which makes line tuning easier and faster especially for bars that have lines like yours
Christian
I've used a big screw driver and just put it through the loops that the pig tails are attached too when checking my line's solo. Work's fine.
With north/duotone click bars you have the option of changing the pigtails between 20cm, 25cm, 30cm and 35cm. At the moment my bar seems to want about 27.5cm pigtails for the centre lines, any other option here? Or just close enough is good enough kind of thing?
Cool thanks folks. If it does matter, i'm still unclear if the goal is:
1. Lines all the same length, with loops extended
2. Lines the same length with loops used as larks head (thus slightly shorter)
(this is compared to the two front lines ending in a knot.)
Well I learned there's a workaround built in: this location for all 4 lines. But it assumes the remainder is unadjusted. fiddly if it needs adjusting.
This means I need to do the RED text in my first post. Use the loop as usual, which shortens it a little, but that has to be done for equal line lengths.
Cignify, this may help you: I saw a video where they put their full weight on individual lines to stretch them out to get equal line length. Perhaps you can do this, or just tie a small knot somewhere to shorten the line.
If they are cab lines (they look like it) you can put a small phillips head (the one they supply) through just under the front line pigtail knots
Yes you can stretch lines by pulling hard using your weight but not sure how long that lasts, maybe enough for the next session. Usually i find one rear line is looser than the other so is probably good practice. If the two front lines are uneven then I'm not sure what the flock to do.
Thank you for allowing me to share my deep knowledge of Cabrinha products, please send me a free kite now.
Cool thanks folks. If it does matter, i'm still unclear if the goal is:
1. Lines all the same length, with loops extended
2. Lines the same length with loops used as larks head (thus slightly shorter)
(this is compared to the two front lines ending in a knot.)
In this case, it doesn't matter how you connect them!
All modern bars have the same ending (whether it is loops or knots) on both centre lines and the opposite ending on the steering lines.
As long as both centre lines are exactly the same length, both steering lines are the same length, the 40 plus cm of bar throw will make the few millimetres of difference between the front and back lines irrelevant.
Just remember to check them when your trim is fully sheated out (centre lines as long as they can go and all 4 lines equal length)
Literally did this two weeks ago.
4 year old kite, started flying really average. Let someone else kite it, who told me it was fked.
Lines were out by about 4 inches. lengthened the steering lines and shortened the middle to try even out.
flys great now.
Hi SirLancelot
What's in a few mm? That was the original question and as per usual it got a little side tracked, but that can be a good thing.
Answer is .... nothing, don't worry about a few millimetres. Remember this: Your kite may not be absolutely perfectly symmetrical. You have usually three attachment points on your steering lines, all varying by more than a few millimetres. ( so obviously the front lines and steering lines do not have to be equal length exactly) . The kite is almost never held stationary and you probably have not got an inbuilt spirit level in your bar or hand so you are probably holding the bar slightly skew anyway.
Now a few centimetres or inches that's a different story.
I agree with Gateman
I will go to a lot of trouble to make sure my Front lines are exactly the same length.
Ill try and get my Back lines close to the same length as each other as I can.
If the relationship between the back and front lines is out by less than a couple of centimetres I'm not going to stress it
Thanks for all the info folks, I fixed the lines, very happy with them now. (made some lines myself since buying them can be a rort!)
Here's a pic for those with Cabrinha lines or similar, and also a link to a video that's probably the best I found to explain how to test line length.
I've used a big screw driver and just put it through the loops that the pig tails are attached too when checking my line's solo. Work's fine.
I said.. As above
Sorry got to cut this short and get back to work. Ha
Bye bye
I've used a big screw driver and just put it through the loops that the pig tails are attached too when checking my line's solo. Work's fine.
I said.. As above
Sorry got to cut this short and get back to work. Ha
Bye bye
Yeah takes a little while for the message to get through but seems boobtube fixed it